Full Bust Adjustment

For this tutorial I am using the Mamma Can Do It Relaxed Fit Peplum pattern.

See my other posts for this pattern too:

 

I chose this pattern because the bodice is a block, which means you can use this tutorial’s method on almost any dress or top.

Fabric Choice

This pattern (whether pleated, gathered, circle or half circle) looks great with a structured knit fabric!  I would recommend a stable knit such as a pontescuba or liverpool.  I used a liverpool from Elevated Fashion Fabrics.  The amount of stretch your fabric has may affect the fit of your garment.  If you’re using a more stable knit, with less stretch, you might be more likely to need a full bust adjustment even if you normally get away without doing one.

 

Do I need a Full Bust Adjustment?

That’s a difficult question to answer.   The usual rule is if your upper bust and full bust measurements are more than 4″ apart then you would need a FBA.  But it really depends on the designer, the fit of the pattern, etc.  Check out the size chart. If you’re one size larger in the full bust than the upper bust, then you should use the smaller size and do a FBA.

Another easy way to know would be if you have made the garment already and you’re noticing your side seam being pulled forward and always having to dug your blouse down.

Measure your bust!

Upper bust – measure just under your armpits, across the top of your chest. This should be a fairly snug measurement.

Full bust – measure across the fullest part of your chest, wearing your usual bra.

Subtract your upper bust from your full bust.

Mine is about 46.5″-42.5″ which is right about 4″.

 

Getting started

Print and assemble your pattern

The great thing about layered PDF patterns is that you can print just your size or sizes if you’re going to grade.

I want to grade to a lower size at the waist for a more fitted look, so I’m printing both my normal size and the size below it.

Be sure to choose the size that matches your upper bust.  Since you’re doing a FBA, the bust measurement on the chart for your size will no longer be a constraint.

Slash and Spread

Another great thing about PDF patterns is that you can reprint, unlike a tissue pattern where you can’t afford to mess up.

I recommend printing two bodices. It’s really helpful for reshaping the armcye after we do the FBA.

I numbered this bodice 1.  It has my grading down at the waist and I’ve marked the outlines of the original pattern piece.

Here’s bodice number 2.  On this one, I start by marking a dot in the center of the bust. I hold the pattern piece up to me to double check the location.

Then draw a straight line to the side seam in line with the bust.

Then connect the center bust point to the bottom center of the armcye.

Finally, mark a line on the inside (fold side) just below the waist. (this protects the waist shape)

Cut the pattern apart at each of these locations.

Hinge from the bust point to add space at the bust.  Add space based on how much more than 4″ difference you have between upper and full bust. I need a minimal adjustment.

Unroll some pattern paper, enough to fit this piece.  If you don’t have pattern paper, you can tape together several pieces of blank paper or tape it to bodice #1 if you printed two.

I marked with purple where I’m adding space.

If you’re confused about the waist space by the fold, it’s to keep the bottom of the bodice aligned and offset the space being added just below the armcye.

I marked in pink where the original bodice was.  We need to reshape the pattern piece to match the original armcye and waist.

I use a french curve to help draw the armcye back in.

You can either use the curve or a straight ruler to connect the waist and armcye.   Use the straight side to connect the waist to armcye.

Here’s what mine looks like –

Now you can cut out your fabric with your new bodice piece and proceed to sew!

Here’s mine.  I also pleated the skirt using this hack (link to my blog post).

 

This post may contain affiliate links.  They don’t change the prices you see, but I might get a small percentage to help fund materials for my next post.
If this post was helpful to you, and you’re planning to purchase the pattern anyway, I’d really appreciate it if you’d use my affiliate link:  MCDI Relaxed Fit Peplum (Women’s/Girl’s/Bundle)

Add a Comment

Your email address will not be published. Required fields are marked *